WHITE SAND REP FR 400 is a high-strength, fiber-reinforced, polymer-modified, microsilica-enhanced cementitious structural repair mortar. It is a ready-to-use repair compound formulated for demanding structural concrete repairs with excellent adhesion, durability, and mechanical performance.
WHITE SAND REP FR 400 is designed for:
- إصلاح الخرسانة الإنشائية.
- إصلاح الخرسانة المسلحة المتضررة.
- إصلاح تعشيش الخرسانة.
- إصلاح الأسطح الخرسانية الرأسية.
- إصلاح الأسطح الخرسانية الأفقية.
- إصلاح الأسطح الخرسانية العلوية (Overhead).
- أعمال الترميم الموضعي (Patch Repairs).
- Rehabilitation of concrete structures
يُناسب غراء واجهات وايت ساند تركيب مجموعة واسعة من أنواع البلاط، بما في ذلك:
- Repairing broken structural concrete elements
- Repairing honeycombed concrete
- Repairing spalled concrete
- Restoring reinforced concrete
- Large patch repairs
- Structural restoration projects
يتميز غراء وايت ساند بريميوم فيكس بالعديد من المزايا، منها:
- مقاومة إنشائية عالية.
- تركيبة مدعمة بالألياف.
- معدل بالبوليمرات.
- Microsilica enhancement
- خصائص عدم الانكماش
- قوة التصاق ممتازة.
- Extremely low permeability
- Corrosion protection for reinforcing steel
- Easy application on horizontal, vertical, and overhead surfaces
- سهولة عالية في التشغيل والتطبيق.
Yes. WHITE SAND REP FR 400 can be applied in a single layer up to 75 مم thick on vertical surfaces thanks to its thixotropic, non-slump consistency.
Yes. It can be applied overhead in layers up to 40 مم thick while maintaining excellent adhesion and workability.
Yes. The repair mortar can be applied up to 100 مم thick in a single layer for horizontal concrete repairs and patch repairs.
WHITE SAND REP FR 400 achieves:
- 30 ميجاباسكال أو أكثر بعد 7 أيام.
- 45 MPa or greater after 28 days
according to ASTM C109.
The repair mortar provides a tensile strength of 1.5 MPa or greater after 28 days according to ASTM C307.
Typical flexural strength values are:
- 4 MPa or greater after 7 days
- 6 MPa or greater after 28 days
according to ASTM C348.
Its fiber reinforcement, polymer modification, microsilica enhancement, high compressive strength, excellent adhesion, non-shrink characteristics, and low permeability make it ideal for repairing reinforced concrete structures.
قبل التطبيق، يجب:
- Remove weak or damaged concrete.
- Cut back to sound concrete (minimum 10 mm depth).
- Remove dust, oil, grease, rust, and contaminants.
- تشبيع الأسطح الماصة بالماء النظيف.
- Grit blast corroded reinforcing steel.
- Replace severely corroded reinforcement if required.
- قص حواف منطقة الإصلاح بمنشار للحصول على حواف منتظمة.
- Clean thoroughly using a brush or compressed air.
Yes. Reinforcing steel should be treated with a corrosion inhibitor, and the concrete substrate should be primed using WHITE SAND PRIME RC acrylic primer and bonding agent. Apply the repair mortar while the primer remains tacky.
Mix approximately 4 liters of clean water per 20 kg bag. Slowly add the powder while mixing with a grout mixer or slow-speed drill fitted with a high-shear paddle. Mix for at least 3 minutes until smooth and homogeneous. Do not prepare partial mixes.
Apply the mortar by hand or steel trowel while pressing it firmly against the substrate and reinforcing steel to ensure complete compaction and adhesion. Finish with a wooden or plastic float before completing the final finish using a steel float.
For thick vertical and overhead repairs, apply the mortar gradually in firmly pressed layers or patches to achieve optimum adhesion between the substrate and subsequent layers.
After application, cure the repair mortar by continuous water curing and covering it with polyethylene sheets, or use the WHITE SAND Cure curing compound to minimize moisture loss.
Yes. Its extremely low permeability helps protect embedded reinforcing steel from corrosion by reducing the penetration of water and contaminants.
WHITE SAND REP FR 400 is supplied in أكياس 20 كجم.
The product has a shelf life of 12 شهرًا when stored unopened in a dry, shaded location below 35°C under proper warehouse conditions.
Clean tools and equipment immediately with clean water before the mortar hardens. Hardened material can only be removed mechanically.
Yes. Wear protective gloves and safety goggles during handling and application. Avoid direct contact with skin and eyes. Wash exposed skin immediately with soap and water, rinse eyes thoroughly if exposed, and seek medical advice if irritation continues. The product is non-flammable and not classified as hazardous under current legislation.
Yes. WHITE SAND REP FR 400 is specifically designed for structural repair and restoration of reinforced concrete, providing excellent adhesion, durability, corrosion protection, and long-term structural performance.
WHITE SAND REP FR 400 delivers superior compressive strength, fiber reinforcement, microsilica enhancement, non-shrink performance, exceptional adhesion, low permeability, corrosion protection, easy application on vertical and overhead surfaces, and long-lasting durability, making it an excellent choice for professional structural concrete repair projects.
