Uses

• Premium decorative coating for interior walls.
• Suitable for properly prepared concrete surfaces.
• Suitable for cement-plaster and rendered surfaces.
• Suitable for compatible gypsum and gypsum-board surfaces.
• Suitable for residential buildings.
• Suitable for offices, schools and commercial buildings.
• Suitable for surfaces requiring a smooth semi-gloss finish.
• Suitable for interior areas requiring a durable, easy-to-maintain coating.

Advantages

• High-quality water-based copolymer-emulsion formulation.
• Attractive semi-gloss finish.
• Excellent adhesion to properly prepared substrates.
• Excellent smoothing and leveling properties.
• Provides a uniform decorative appearance.
• Good resistance to dirt pickup.
• Excellent resistance to ultraviolet radiation.
• Good durability.
• Very low VOC content.
• APEO-free formulation.
• Formulated without added formaldehyde or ammonia.
• Available in white and other selected colors.
• Water-based and easy to clean before hardening.
• Non-flammable.

Substrate Preparation

The substrate must be structurally sound, clean and free from dust, oil, grease, loose particles and other contaminants or foreign materials that may reduce adhesion.

Remove weak or loosely adhering material using a suitable preparation method. Fill cracks, holes and surface imperfections with a compatible repair or filling compound before applying the primer.

Priming

Apply one coat of a suitable WHITE SAND PRIMER SEALER before applying WHITE SAND PREMIUM EMULSION SEMI-GLOSS. Allow the primer to dry completely before applying the finishing coats.

Application Conditions

• The substrate temperature during application must not be below 10°C.
• The substrate moisture content must not exceed 8%.
• The relative humidity in the working area must not exceed 70%.
• The substrate pH must not exceed 9.
• Do not apply to wet or damp surfaces.
• Provide adequate ventilation during application and drying.
• Do not apply a subsequent coat until the preceding coat is fully dry.

Mixing and Dilution

Stir WHITE SAND PREMIUM EMULSION SEMI-GLOSS carefully before application until a uniform consistency and color are obtained.

If required, add a suitable quantity of clean tap water to obtain the correct application viscosity. The required quantity depends on the substrate, application equipment and ambient conditions. Avoid excessive dilution.

Application

1. Ensure that the substrate is correctly prepared, primed and completely dry.
2. Stir the product thoroughly before application.
3. Add clean tap water only when viscosity adjustment is required.
4. Apply uniformly using a suitable roller, brush or spray equipment.
5. Maintain a dry-film thickness of approximately 50 microns per coat.
6. Ensure complete coverage and maintain a uniform semi-gloss appearance.
7. Allow each coat to dry fully before applying the subsequent coat.
8. Protect the applied coating from dust, moisture and contamination until dry.

Yield and Coverage

The theoretical coverage of WHITE SAND PREMIUM EMULSION SEMI-GLOSS is approximately 16 m² per kilogram at a dry-film thickness of 50 microns.

Under practical site conditions, coverage may be approximately 12 m² per kilogram. Actual consumption depends on substrate condition, porosity, application method, film thickness and material wastage.

Cleaning

Clean all tools and application equipment with water immediately after use. Hardened material must be removed mechanically.

Storage and Shelf Life

WHITE SAND PREMIUM EMULSION SEMI-GLOSS has a minimum shelf life of 12 months when stored in its unopened and undamaged original packaging in a dry and shaded location, protected from direct sunlight, at an ambient temperature below 35°C.

Packaging

• 4 kg plastic pails.
• 20 kg plastic pails.

Health and Safety

• Wear suitable protective gloves and safety goggles during handling and application.
• Avoid unnecessary contact with the skin and eyes.
• In case of skin contact, wash immediately with soap and clean water.
• In case of eye contact, rinse immediately with plenty of clean, cold water.
• Seek medical advice if irritation continues.
• The product is non-flammable.
• The product is not classified as hazardous under current legislation.
• Do not dispose of the material in water or soil.
• Follow applicable local disposal regulations.

Quality and Technical Support

WHITE SAND products are developed and manufactured under a quality-oriented product-development process and an independently standardized quality management system.

WHITE SAND provides technical assistance regarding substrate preparation, primer selection, dilution and the application of premium interior emulsion coatings.