الاستخدامات

• Surface hardening of warehouse floors.
• Factory and workshop floors.
• Loading bays and logistics areas.
• Car-park floors.
• Power-station floors.
• Floors subjected to heavy traffic.
• Concrete floors requiring enhanced abrasion and impact resistance.
• Suitable for wet areas.

المميزات

• Monolithic cementitious dry-shake floor hardener.
• High resistance to abrasion and impact.
• مقاومة ضغط عالية.
• Resistant to petrol, oils, grease and mineral solvents.
• Non-metallic and non-rusting.
• Produces a dense, hard-wearing concrete surface.
• Reduces surface dusting.
• Easy-to-clean finished surface.
• Suitable for wet areas.
• Available in a range of colors.
• Factory pre-mixed for consistent application.

Concrete Requirements

FLOOR M10 must be applied monolithically to freshly placed concrete. The concrete mix, placing, compaction, levelling and finishing procedures must be appropriate for the intended industrial-floor performance.

Apply the product after bleed water has evaporated and when light foot traffic leaves an imprint approximately 5 mm deep in the fresh concrete.

طريقة التطبيق

1. Place, compact and level the fresh concrete according to the project specification.
2. Allow bleed water to evaporate completely.
3. When the concrete reaches the correct plastic stage, smooth the surface using a mechanical trowel.
4. Broadcast FLOOR M10 evenly over the fresh concrete at approximately 3-5 kg/m².
5. For colored floors, divide the total quantity into two applications to improve color uniformity.
6. Allow the dry-shake material to absorb moisture from the concrete.
7. When the material appears uniformly darkened and moistened, work it into the surface using a wooden float or power float.
8. Complete the final finish using a steel trowel.
9. Do not excessively burnish the final surface.
10. On large floors, carry out progressive finishing immediately behind the placing team.

المعالجة

Begin curing immediately after final finishing to reduce water evaporation and help prevent crazing, blooming and loss of mechanical performance.

Apply a suitable WHITE SAND curing system or cover the complete surface using polyethylene sheets securely taped at the edges.

معدل التغطية والاستهلاك

Apply FLOOR M10 at approximately 3-5 kg/m².

Actual consumption depends on the required abrasion resistance, floor color, concrete condition, application method and project specification.

التنظيف

يجب تنظيف الأدوات والمعدات بالماء النظيف فور الانتهاء من التطبيق وقبل تصلب المادة. أما بعد تصلب معجون إصلاح وتشطيب الخرسانة من وايت ساند، فلا يمكن إزالة المادة إلا بالطرق الميكانيكية.

التخزين ومدة الصلاحية

FLOOR M10 has a minimum shelf life of 12 months when stored in unopened and undamaged original packaging in a dry, shaded place, away from direct sunlight, at an ambient temperature below 35°C.

العبوات

• أكياس ورقية وزن 20 كجم.

الصحة والسلامة

• Wear suitable protective gloves, safety goggles and a suitable dust mask during broadcasting and application.
• يجب تجنب الملامسة غير الضرورية للجلد والعينين.
• Avoid inhaling airborne powder during dry-shake application.
• Wash skin contact immediately with soap and clean water.
• في حال ملامسة العينين، يجب شطفهما فورًا بكمية وفيرة من الماء النظيف والبارد.
• يجب استشارة الطبيب إذا استمر التهيج.
• المنتج غير قابل للاشتعال ولا يُصنف كمادة خطرة وفقًا للتشريعات الحالية.
• Follow applicable local disposal regulations.

الجودة والدعم الفني

يتم تطوير وتصنيع منتجات وايت ساند وفق عمليات تطوير تركز على الجودة ونظام إدارة جودة معتمد من جهة مستقلة.

WHITE SAND provides technical assistance regarding concrete-floor design, application timing, broadcasting rate, power floating, finishing and curing.